Golf Club Regular
Golf Club Regular
 |
US $125.00
How often you replace your fists depends on how often you play and what the climate we live in may also depend on where you keep your clubs stored.
If you play four times a week or more in extreme temperatures and humidity, then you may need to change handles every six months or so because sweat, heat, moisture, dirt and sand all tend to break the grip finish. They quickly lose their elasticity when used a lot. If you leave the clubs in the trunk of his car on a hot day of extreme heat the material to deteriorate even faster. If you only play occasionally and keep bats away you can go long, but most golf experts indicate that the handles must be changed every 18 months to two years.
Replacing grips is itself fairly easy repair, just a few simple tools. Replacing grips is not expensive, even when you take them at their local golf shop, but if you are as I take them and hoping their two or three days to return that is the problem. Since you only have to select the handles that I want in my golf shop and then do the repair myself.
Materials needed:
- New grips.
- A t-shirt.
- Bank press (will be easier).
- Rubber holder axis for the defect to protect them from damage while the shaft is held in the press.
- Double Grip tape face.
- Scissors.
- A grip tape scraper.
- Utility knife with a hook instead of a blade tip (blade pointed to damage graphite rods.
- Grip solvent.
- Container to collect the solvent.
- Old Rag.
Preparation:
Collect grips you like in your shop, you can catch the double-sided grip tape and other materials you need.
The first time you replace I grab my was slightly nervous about cutting off my grips, I started with my least used club for me is my 3 iron, my thinking was that if I messed it up, I could at least still play and take the club in a repair shop. After the first 3 iron, I realized that was simple enough, but if you have the same concern go ahead and try that first.
The process is fairly simple, but its importance to plan the steps. The handles are made with double-sided adhesive tape, the hard part is to slide the new grip on this tape, and just use that grip solvent that allows grip to slide into the tape and then evaporates quickly.
STEP 1
Hold one end of the golf club securely under his arm, looking at the handle end forward. Hook knife handle (remember to use a hook blade) and cut the shaft. Be careful not to nick the shaft, especially if it is graphite. Peel the mango of age.
Caution: Make sure that no part of your body is on the road in case the knife slips, and nobody is against you or your side. Always cut away from your body.
STEP 2
Remove the old grip tape underneath, this will mean peeling and scraping. It is also possible that the use of solvents, such as grip solvent or paint thinner, to clean any residue remaining.
STEP 3
Let the shaft to dry completely.
STEP 4
Place the golf club in vice make sure you use a rubber shaft holder so that will not damage the finish. Be careful not to tighten too much, especially if you are working with graphite shafts. Just make sure the shaft is not moving. Position perpendicular to the floor club.
Apply double-sided tape grip on the shaft of the same length as the new grip. Wrap around the shaft, leaving a half inch dominating the final.
Remove the backing from the double-sided tape. Turn half-inch overhang and push inside the shaft.
STEP 6
Push a golf tee in the vent hole in his grasp the new grip and pour solvent in which the other (open) end.
Now pour the solvent control over the entire length of the new grip tape (you'll need a container at the club to take the excess solvent).
Remove the "T" grip hole
STEP 7
Quickly position the opening of the new control on the axis (align gently upwards). Squeeze the handle and slide the grip on the shaft. Continue sliding and pushing until you feel the shaft against the end.
STEP 8
Remove your new dam club bench press. Hold the club in its normal playing position and the position and ensure that your grip is right. If you need to make adjustments, turning the handle to achieve the desired alignment.
Clean the handle and shaft with a clean cloth.
STEP 9
Leaving the club back down and took dry. I always let my clubs to sit for 12 hours to ensure they are fully tightened.
That's it now has a whole new sense for their clubs. Once you realize how easy it is likely to be replaced more frequently, and to help lower the golf scores.
Joe Fox writes articles for http://howtorepairanything.net your resource for tips and how to advice for repairing anything around the home or garden.